Prout 37
Snowgoose Elite
1993
Cruising Catamaran
Sold!!!
Thanks for Looking
"EXPOSURE"
1993 PROUT SNOWGOOSE 37 ELITE
SPECIFICATIONS AND INVENTORY
Note 1: MEASUREMENTS
Dimensions, capacities, weights and descriptions are based on actual measurements or data published and/or provided by Prout Catamarans Ltd. and/or product manufacturers.
Note 2: CLASSIFICATION OF EQUIPMENT AND GEAR
S = Prout Standard O = Prout Optional Extra C = Prout Custom Extra
U = Upgraded from Prout Standard or Option A = Added by Owners
Note 3: ITEMS INCLUDED BUT NOT FITTED
Items included but not fitted are noted "(NF)" (not fitted) if components only are to be supplied with the vessel. If only specific components are so denoted, all other components for that item are fitted. All equipment, fittings, fasteners, hose, wire, etc. required for fitting these items are included in the inventory, as are detailed installation instructions and/or diagrams.
1.0 STATISTICS
1.1 HULLS AND DECK
Length Overall 36ft 7in 11.15m
Length of Hull 35ft 7in 10.85m
Length Waterline (LS) 32ft 7in 9.93m
Maximum Beam 16ft 3in 4.95m
Maximum Hull Beam 4ft 3in 1.30m
Draft (LS) 2ft 8in 0.81m
Displacement (LS) 11,500 lb 5216 kg
1.2 INTERIOR
Maximum Headroom
- Bridgedeck 5ft 11in 1.80m
- Hulls 6ft 6in 1.98m
Double Berths (2)
- Width (max) 4ft 9in 1.45m
- Length 6ft 11in 2.11m
Single Berths (2)*
- Width 2ft 2in 0.66m
- Length 6ft 6in 2.98m
*convertible salon settees
1.3 TANKAGE
Freshwater 138 US gal 525 liters
Holding 26 US gal 100 liters
Fuel 40 US gal 155 liters
1.4 SPARS
Mast
- Above Deck 40ft 0in 12.19m
- Above D.W.L. 47ft 5in 14.45m
Boom (including gooseneck) 11ft 0in 3.35m
1.5 SAILS
Mainsail 200sq ft 18.58sq m
Genoa 416sq ft 38.65sq m
Staysail 84sq ft 7.80sq m
Cruising Spinnaker 872sq ft 81.01sq m
2.0 CONSTRUCTION
2.1 GENERAL
S Hand laminated in temperature controlled facilities.
S Top quality Lloyds approved materials.
2.2 HULLS AND BRIDGEDECK
S Solid GRP lay-up incorporating bi-axial fibers with reinforcement in high stress areas.
S Isophthalic type gelcoat used, with the first layers of powder bound fibers laid down with isophthalic resins, using the Scott Bader System for protection against osmosis.
2.3 DECK
S Laminate cored with end grain balsa in horizontal areas, with plywood pads where fittings are sited.
S Bi-axial fibers incorporated in the lay-up, with reinforcement in high stress areas such as chainplate locations.
U Moulded non-slip areas painted with matt Awlgrip linear polyurethane with "Griptex" added, providing both superior non-slip and glare reduction.
2.4 BULKHEADS
S Marine plywood bulkheads bonded to hulls and deck with CSM and "stitched" to hulls with unidirectional rovings.
2.5 INTERIOR FURNITURE UNITS
S Units moulded GRP or fabricated marine plywood.
S All units bonded to hulls and deck assembly with CSM.
2.6 BUOYANCY
S Built-in buoyancy compartments forward and aft in each hull.
S Water tanks, located in hulls, form a double bottom in that area.
S Nacelle is foam filled.
2.7 HULL/DECK JOINT
S External flanges bonded and riveted together then entire joint bonded on inside with GRP before flanges trimmed.
2.8 FITTING OF EQUIPMENT
S All cutouts in cored deck areas sealed with gelcoat or epoxy.
S Stainless steel (SS) backing plates or large diameter washers fitted to all thru-bolted fasteners.
S All equipment and fittings bedded and sealed with marine grade sealants.
3.0 HULLS AND DECK FEATURES AND FITTINGS
3.1 HULLS AND BRIDGEDECK
S/U "Bright White" gelcoat with custom striping . Stripes are "Bright Green" and "Bright Yellow".
S Hull/Deck joint covered with anodized aluminum rubrail with moulded rubber insert. Bows and sterns covered with matching GRP moulding.
S Central full length nacelle to provide foredeck lockers, lower seating in salon allowing low profile main cabin coachroof for less windage, fuel tank locker under cockpit, and engine bay aft.
S Skeg hung rudders.
S Sillette drive leg and engine exhaust fitting mounted on nacelle transom, heater exhaust fitting on port bridgedeck transom.
S SS stern swim steps with white "Kingboard" tread, port & stbd.
C/A Bronze Dynaplate port hull aft for SSB and aft of midships port and stbd inboard for lightning ground.
A Bottoms, including rudders and nacelle, coated with one coat of C-Defence epoxy and 3 coats of C-Defence "Copperbot" epoxy/copper to resist osmosis and provide long term antifouling. Currently coated over with Petit Trinidad SR bottom paint.
3.2 DECK
3.2.1 GENERAL
S/U Gelcoat is "Bright White" with "Bright Green" accent band around cabin
U Non-slip deck areas are finished in polyurethane paint. Color is pale gray matt.
3.2.2 FOREDECK
U/E 30in high SS double rail bowrails, port & stbd, w/ double lifelines across front of foredeck. Gibb pelican hooks on lifelines.
S Lead block for genoa furling line fitted to starboard bowrail.
A Chocks on bowrails for whisker pole.
S Solid foredeck incorporating two large self-draining lockers with GRP hatch covers.
S/C Anchor/rode locker forward, fore/aft divider bulkhead, SS U-bolts for anchor chain. Hatch fitted with hasp and lock.
S/C/A Sail/LPG locker aft of anchor/rode locker. Custom rack for LPG cylinders. Hatch cover fitted with gasket and SS "Bailey Locks". Locking system accessed through anchor/rode locker.
S 10in aluminum 4 bolt deck cleat w/ SS rubbing strakes on bows. (NF: strakes)
O SS U-bolts on bows for spinnaker downhauls.
3.2.2 FOREDECK (continued)
A Custom SS anchor bowrollers (Bruce & Delta) inboard of bowrails port & stbd. (In lieu of standard single aluminum roller)
S/O SS anchor guards, port & stbd, under rollers.
A Dual Simpson Lawrence Anchorman GD1000 electric windlasses over anchor locker port & stbd, and 10in aluminum 4 bolt deck cleats aft.
A SS landing plates between anchor rollers and windlasses.
A Washdown hose quick coupler in hawse pipe forward of anchor locker, ballvalve in locker.
O Deckplate for holding tank pumpout, winch handle socket on cap, at port corner of main cabin.
3.2.3 SIDE DECKS
U 30in tapered SS stanchions with double lifelines. Gates with pelican hooks port & stbd at stern rails.
S Lead blocks for genoa furling line fitted to stanchions stbd side.
S Moulded toerails between stanchion bases.
S SS handrails on main cabin deck outboard.
S 10in aluminum 2 bolt spring cleats amidships.
C/A Track w/ mounts for detachable swim/boarding ladder at lifeline gates port & stbd. Bi-fold SS ladder. ("Step-Away" type)
C SS grab handles on aft cabin decks, outboard aft, above ladder mounts.
3.2.4 AFT DECK
U/S 30in high SS double rail stern rail port & stbd, w/ double lifelines across aft crossbeam. Pelican hooks on lifelines. Stern light on stbd stern rail.
S Lead block for Genoa furling line fitted to stbd stern rail and 6in aluminum cleat fitted to inboard side of stbd aft cabin house at cockpit coaming.
S/A 10in aluminum 4 bolt deck cleat stern.
S Large hatch, with GRP cover, in aft deck/cockpit coaming for access to engine bay . Hatch cover fitted with locking pin accessed from inside engine bay.
S Inspection trap w/ hinged clear acrylic cover, aft of engine bay hatch, to view drive leg and exhaust.
U/S Hatch on aft beam w/ GRP cover fitted with bolts, for access to steering components and wiring. Inspection cover on sterns for access to rudder stocks.
S/A Shore power inlet fittings (USA type),110/120VAC (2 ea. One for HVAC and one for house supply) and 220/240VAC on cockpit coaming stbd side.
C/A LPG valve for BBQ w/ SS cover on aft cross beam under stbd stern rail.
A Mount for BBQ on stbd stern rail side rail.
O/C SS anchor guards on aft beam, port & stbd.
A SS stern anchor roller with 8in aluminum deck cleat on aft deck inboard of port stern rail.
A St Croix SS stern rotating davits with 9:1 lifting ratio.
A St Croix SS removable lifting crane with 7:1 lifting ratio.
3.2.4 AFT DECK (continued)
A Ankarolina flat web anchor line reel mounted on port stern rail aft rail inboard. Rail mount for Fortress anchor on aft rail outboard. Rubber bucket for anchor chain on aft beam under reel.
A SS pole w/ GPS antenna on aft cross beam outboard fastened to port stern rail.
A Outboard motor mounting pad on port stern rail side rail.
A "Lifesling" MOB retrieval system mounted on stbd.
A Horseshoe buoy stbd stern rail.
A Coaming pad eye used with Vang/Preventer to hold boom when cockpit enclosure fitted.
3.2.5 BRIDGEDECK CABIN
S Running (navigation) lights on cabin sides.
S 10mm (3/8in) bronze tint acrylic (plexiglass) windows, flush fitted in cabin face and sides.
S SS mast tabernacle on mast step just forward of cockpit.
U Lewmar staysail traveler forward of mast. Control lines led aft through canopy base to cockpit. Sheet led forward to block on inner forestay fitting, then aft through deck turning block and fairlead to cockpit.
U/E Lewmar "Ocean" hatches w/ bronze tint acrylic glazing: 2 x Size 60 on centerline, 2 x Size 20 port & stbd outboard above handrail.
C SS vent fitting for water heater inboard of forward small hatch port side.
A Nicro 4in SS "Day/Night" solar vent port & stbd forward of small hatches.
A Nicro 4in 12VDC SS vent aft of small hatches stbd side.
3.2.6 AFT CABINS
S Moulded step from side decks to aft cabin decks at main cabin bulkhead.
C Lewmar Size 3 opening portlight w/ bronze tint acrylic glazing in cabin side port & stbd.
U Lewmar genoa track & car inboard on cabin decks. Spinlock double jammer foot block aft, leading control lines and sheets to cockpit and winches.
U/O Lewmar "Ocean" hatches, w/ bronze tint acrylic glazing: Size 40 in aft faces of cabins, Size 10 on decks outboard of genoa track.
3.2.7 COCKPIT
O/C/A GRP canopy over cockpit with clear acrylic windshields (windscreens) port & stbd. Wraparound SS handrail both sides and aft. Nonslip on top deck.
Overhead viewing panel w/bronze tint acrylic glazing. 6ft 4in headroom at
helm. Custom removable side and back panels in waterproof Sunbrella fabric w/ clear acrylic windows to enclose cockpit. GRP bottom rails for side panels. Back panel extended aft from canopy with SS support hoop to provide vertical aft panel. (Note: New enclosure panels 2003).
A Demister/fan for starboard windshield.
A Red/White LED dome light overhead on centerline.
A Waterproof cable glands for mast wiring through canopy and through cabin deck under stbd windscreen.
S/U SS roller on edge of cabin deck/bulkhead for leading halyards from bottom of mast. Lewmar 30ST halyard winch and 4 aluminum jam cleats on bulkhead under roller.
U Spinlock line clutches on coachroof inside canopy for staysail sheet, stbd, and control lines, port & stbd.
U/A Companionway door on port side of cabin bulkhead, one-piece 12mm (15/32in) bronze tint acrylic w/ SS lift-off hinges. Storage cover in green acrylic with zippered closure.
S/A Integrally moulded steering and instrument console with hinged bronze tint acrylic lid on stbd side of cabin bulkhead. Soft grip SS steering wheel on front of console, w/ steering lever for drive leg under, just above sole. Single lever engine controls on stbd side. Engine instrument panel and hour meter, switches and indicator lights for windscreen demister, windlass breaker/switch and emergency battery connector switch on top of console. 2 x 12VDC sockets on port side. SS louvered vents on upper stbd side and lower port side.
U/A Radar display, VHF radio, GPS receiver, autopilot compass/control head, display units for wind speed, wind direction, Knot Log, fish finder/depth sounder, electronic steering compass and control, fitted to bulkhead over helm console.
S Integrally moulded "L" shaped seats port & stbd.
O/U Seat cushions, 4 piece set. 2in closed cell foam with reversible covers of green acrylic one side, white vinyl reverse.
S Lewmar Size 4 opening portlights, w/ bronze tint acrylic glazing, in faces of side seats.
S Manual bilge pumps fitted into faces of aft seats.
A Garelick removable gunwale seats port and starboard. Fold-up footrest on helm console.
S Integrally moulded raised winch platform between aft seats and over engine bay. Deck plates w/ winch socket caps for water tank fill port & stbd. Top hinged door for access to engine bay in face. Release lever and line w/ cleat for raising
3.2.7 COCKPIT (continued)
drive leg on stbd side. Rubber stops fitted to face of platform above door.
U/A 2 x Lewmar 48ST sheet winches on platform. Lewmar mainsheet traveler across top of cockpit coaming and platform. Camcleats for spinnaker downhauls on top of cockpit coaming at outboard ends.
C/A Custom swing up cockpit table fitted to engine bay door. Removable SS support leg stored in clips beside door.
S Cockpit draining through integrally moulded self-draining fuel tank locker under center of cockpit. GRP cover over locker. SS fuel tank.
S/C/A Self-draining lockers under cockpit sole, port & stbd. Hinged GRP hatch covers, each fitted w/ 2 x SS "Bailey Locks".
3.2.8 ENGINE BAY
S Accessed from cockpit and aft deck.
O Fully lined on all sides and overhead with acoustic foam insulation.
A Dome light overhead.
S One piece GRP liner with integral engine bearers, oil drip pan and bilge.
O/A Yanmar 3 cylinder 38hp FWC diesel auxiliary engine fitted w/ high output alternator and Seafrost refrigeration compressor.
O/U Eberspacher (Espar) diesel fuel cabin heater mounted on port side.
C Seafrost AC refrigeration mounted on stbd side outboard. Dedicated 110VAC receptacle.
C Engine drive refrigeration components and seawater strainer mounted on acrylic board on stbd side inboard.
A Dual Racor diesel fuel filters mounted on aft bulkhead. Selector valves mounted on acrylic board on stbd side inboard.
C "Smart Alternator Regulator" on forward bulkhead port side.
4.0 INTERIOR FEATURES AND FITTINGS
4.1 GENERAL
4.1.1 JOINERY
S Bulkheads, doors and wood furniture units faced in American Cherry veneer with solid cherry mouldings and trims, except where stated otherwise. All veneer facings, wood mouldings and trims finished in sprayed two-part polyurethane lacquer.
U Veneer bulkhead trims throughout.
S Bulkheads, cabin door and hull sides in head compartment and shower stall faced in silver grey pattern Formica.
S Radiused corners on doors, drawer fronts, counter tops, mouldings and trims.
S Locking handles on all cabin doors.
A Self-latching door stops on cabin doors and shower door.
S Double action push button catches for locker doors and drawers.
S Carpet trims on base of bulkheads and aft cabin lockers. Capped with wood trims on bulkheads.
4.1.2 GRP MOULDINGS
S Units for salon settee, navigation area console/chart table and outboard counter/locker units, galley inboard and outboard counter/locker units, aft cabin
sole/berth/seat units and 1 piece unit for head compartment below beltline. Horizontal surfaces cored with balsa.
S Wood furniture units, locker doors and drawer fronts for galley and navigation area finished in sprayed two-part polyurethane paint to match GRP furniture units.
S GRP mouldings and painted wood modules in light gray. Matching locker doors and dark gray drawer fronts in galley and navigation area.
S Settee, aft cabin berths and seats faced with carpet.
4.1.3 LOCKERS
S All surfaces inside hanging lockers faced with 12mm foam backed vinyl
S Wood surfaces inside all other lockers finished in sprayed polyurethane lacquer or brushed grey rubberized paint. Hull and deckhead surfaces finished with brushed flocoat or grey rubberized paint.
A Hull and deckhead surfaces in shelf lockers insulated with closed cell neoprene foam, 8mm (5/16in) above waterline, 16mm below. Insulation covered with 12mm (15/32in) foam backed vinyl.
4.1.4 HULL AND DECKHEAD
S Visible hull and contoured deckhead surfaces faced with white12mm (15/32in) foam backed vinyl.
4.1.4 HULL AND DECKHEAD (continued)
S Removable ply panels, faced with white 4mm (5/32in) foam backed vinyl, on all flat deckhead surfaces. White button caps on screw heads.
4.1.5 SOLE
S Ribbed, wear and moisture resistant carpeting in "Washington Jade" (blue/green) on all areas except galley, stbd forward cabins, head compartment and under salon table.
S Vinyl flooring in mottled grey/white in galley and starboard forward cabin.
S Vinyl flooring in simulated teak under salon table.
4.1.6 Windows, Ports, Hatches and Ventilators
S White moulded GRP window trims.
S/U Ports fitted with white plastic trims and flyscreens.
S/U/A Hatches fitted with white plastic trims and aluminum frame flyscreens.
A Power vents fitted with white plastic trims.
4.2 ACCOMMODATION DETAILS
4.2.1 BRIDGEDECK SALON
S 2 large windows forward over audio/video locker.
S 2 large hatches overhead, opening forward.
A Bug screen curtain available for cabin entrance doorway, fitted with snap fasteners.
C/A U-shaped settee, 8ft 6in long, seats 9. Cushions in "soft tufted" style covered in wear resistant, polyester, burgundy Chenille, Teflon treated for stain and soil resistance. 4 matching scatter cushions. (Recovered 2002). 4 co-ordinated scatter cushions in "Como Larkspur" (blue/green/purple/burgundy/gold).
C/U/A Seat cushions 21in deep, with 1in knee roll, of 3in high density CM60 foam with polyester "Luxbond" facing. Back cushions of medium density CM40 foam, 3in thick at bottom tapering to 2in at top. Faced with polyester "Luxbond".
S/A Storage lockers under settee all around.
S/C Custom table in white King Starboard with folding hinge on centerline to allow for walkway access to forward storage lockers.
C Custom lockers forward of settee. Sliding doors over lockers and removable bottom boards with additional storage under. Air Conditioning unit mounted in starboard locker.
A 110VAC single socket and 12VDC terminal block under audio/video shelf
A TV mounted on forward port side of salon with antenna booster control on bulkhead at shelf behind port settee. 12VDC socket on shelf.
A Fans on bulkheads forward of settee - 1 port, 1 stbd.
S/C Fluorescent lights above shelves behind settee backs - 2 port, 2 stbd.
4.2.1 BRIDGEDECK SALON (continued)
U LED reading lights on bulkheads at forward corners of settee - 1 port, 1 stbd.
O Heater duct under entrance step.
A Air conditioning duct at forward end of salon, with adjustable direction louver.
C Large access panel under companionway door for access to water pump, selector valve and 1 service battery.
S Locker at top of port panel inside companionway door.
A 2 x night courtesy lights, red LED, at steps to hulls.
4.2.2 CONSOLE LOCKER
S Double doors in salon aft bulkhead. Access to steering, throttle/gear selector control, console and helm electronics and electrics.
C/A Shelf with 110/120VAC inverter/charger and 220/240VAC battery charger.
A SS louvered ventilator plates in console housing, port & stbd, for inverter and charger.
U/A 2 x 110/120VAC & 220/240VAC AC Main breakers, 110/120VAC branch breaker box, galvanic isolator and 2 x 240VAC single sockets on stbd side.
A DC high amperage distribution cabinet w/ grey acrylic door, mast/cockpit wiring terminal boxes and bus bar and autopilot computer on port side.
S/U/A Removable bottom boards for access to engine start battery, 2 service batteries, "Isolator Eliminator" and wiring runs under.
4.2.3 PORT AFT CABIN
U/O Medium hatch aft, opening upwards. Small hatch overhead, at head of berth, opening forward.
S/O Extra large port opening to cockpit and large port opening to side deck.
S Large double berth with dressing seat. 2 large lockers under berth. SSB antenna tuner and ground plate studs in aft locker.
U Full width fiddles on head of berth and front of seat to retain cushions.
S Berth and cabin seat cushions covered in "Como Larkspur" pattern wear resistant blended fabric w/ "Scotch Guard" finish. Seat cushion in "soft tufted" style.
U Berth cushions of 3-1/2 in memory foam with extra high density closed cell foam on the bottom, seat cushion of 3in CM60 high density.
A Custom, fitted, combination bedding set w/ storage bag,. Zippered interchangeable halves with cotton/polyester shells with polyester fill. "Winter" (10oz), "summer" (5oz) and "tropical" (shell only, no fill) halves. Green exterior and grey lining with fitted beige sheets with Velcro attachment strips and matching pillow cases. Set reversible by switching port to stbd aft cabins.
U/C/A Inboard shelf locker with utility locker under. Doors on lockers. Diverter valve for port bilge pump and studs for lightning ground plate in utility locker.
U Halogen light on inboard locker bulkhead.
O 110VAC double socket on inboard locker bulkhead.
O Heater duct under utility locker door.
4.2.3 PORT AFT CABIN (continued)
U Outboard shelf locker and vanity. Hinged top on vanity with mirror on underside, 2 drawers and small locker with door under. Door on shelf locker.
A Fan over outboard locker.
S Access panel to stern compartment at foot of berth.
S/A Trap in sole for aft bilge sump.
4.2.4 NAVIGATION STATION
S 2 large long windows outboard.
O Small hatch overhead, opening to side deck.
U/S Liquor locker, outboard aft, w/ custom bottle rack and storage locker under. Counter unit forward w/ 3 drawers and 3 shelf lockers under.
U Fluorescent light over counter.
S/A Navigation console/counter unit, inboard, w/ full size slide-out chart table, 3 shelf lockers under. Hinged chart table top w/ SS spring hatch holder, stowage under. Removable panel in console for access to electronics and electrics. Shelf on top of console.
S Flex arm chart light over chart table.
A Icom IC-706 MKIIG HF/SSB radio, GPS repeater, Navman Repeater display and ESP display/control panel in console over chart table.
U DC breaker panels on hinged door at forward end of navigation console.
A 2-12 VDC sockets on console face over aft counter end.
O 110VAC double socket on inboard locker face, forward, at chart table.
A Night light, red LED, at forward bulkhead above sole.
S 3 x traps in sole for water tank inspection covers.
4.2.5 HEAD COMPARTMENT
U Louvers in lower cabin door.
S/A Windows outboard and forward w/ "Fablon" patterned translucent vinyl appliqué for privacy.
S Small hatch overhead opening to side deck.
A Day/Night solar vent forward of hatch.
S/U/A One piece GRP moulding to beltline. Full length shelf outboard, full length shelf inboard with integral vanity sink. Single lever mixer faucet. Locker under sink. Toilet platform forward, inboard. Trap in sole for toilet discharge seacock. Teak grate over bilge sump. Bilge pump pickup in sump.
U/A LPG water heater on inboard bulkhead aft, vented through deckhead.
A/C LPG and CO fume sensors unit in panel under heater.
4.2.5 HEAD COMPARTMENT (continued)
U Shelf at top of GRP moulding, full length on inboard bulkhead and to cabin door on aft bulkhead.
O 110VAC double socket over inboard moulding shelf, aft.
S/A Hanging locker, with door, forward. Access panel to bow compartment. Washdown pump and windlass solenoids in bow compartment. Trap in sole for toilet and washdown intake valves.
S RM 69 marine toilet.
O Toilet holding tank on bridgedeck shelf in hanging locker. Selector valve and tank discharge pump on forward bulkhead beside toilet.
S Teak framed mirror on bulkhead over sink.
S Fluorescent light over mirror.
S Towel ring, roll holder, toothbrush/glass holder and soap dish.
4.2.6 STARBOARD FORWARD CABIN
U Louvers in lower cabin door.
S/A Windows outboard and forward w/ "Fablon" patterned translucent vinyl appliqué for privacy.
S Small hatch overhead opening to side deck.
A Day/Night solar vent forward of hatch.
S Fluorescent light over cabin door.
U Shelf locker, w/ door, inboard aft. Fiddles on top of locker.
O 110VAC double socket at base of inboard locker.
O Heater duct at bottom of inboard locker.
C Triple shelf locker, with doors, outboard aft.
C Sit shower stall, forward, separated from cabin by partial bulkhead with bronze acrylic top panel and door. Shelves inboard and outboard. Swing-up seat for access to hanging locker. Moulded GRP pan with teak grate.
U "Telephone" shower head with shut-off valve, on flex hose. Single lever mixer control.
C Splash proof halogen light on inboard bulkhead in stall.
U Hanging locker for foul weather gear, with door, forward of shower. Doorway gasket. Access panel to bow compartment.
C/A